Why is My Dishwasher Leaking?

Coming downstairs to step in an ominous puddle coming from the dishwasher is never the best to start the day.

Fortuitously, most everyday sources of dishwasher faults are relatively straightforward to diagnose and fix on your own. Meaning you might not have to hand wash the dishes for more than a day or two, call an engineer or need to pay the call-out charge.

So, grab the instruction manual if you can, clean up the mess and get a towel clean up any further spills and so see whether you can’t diagnose the fault. If you cannot call us for local dishwasher repair.

Everyday Explanations of Dishwasher Leaks as well as How to Fix Them

Some of the most common explanations of dishwasher faults are not actually due to a dishwasher fault . Before you start preparing yourself for an engineering task as well as flicking through endless online videos there are a couple of issues you might want to rule out first.

  1. Investigate to see whether your dishwasher is aligned. If your dishwasher is wonky water will easily pool as well as spill out regardless of whether or not the dishwasher has a fault.
  2. Check you have been using the correct detergent. You could be familiar with this fault with your washer. Too much soap or using the wrong type may result in an excess of bubbles, the suds overflow and so you get a spill.
  3. Investigate your dishwasher door closes correctly. If there’s a gap there may be a blockage, or you may need to fix the hinge or the locking mechanism.
  4. Investigate the filter at the base of the tub for any obvious obstructions as if your dishwasher isn’t emptying correctly this can result in overfill and leak.

If none of the above issues apply it’s time to roll up your sleeves and really begin the inspection.

The easiest place to start is the door as well as check for any obvious issues within of the machine before you move on to the underneath. If you can identify as well as mend the issue without pulling out the dishwasher you’ll save yourself a lot of hassle.

Before you do anything else make sure you disconnect the appliance.

Door Seal

The door is seemingly the most common area for leakage and one of the easiest problems to solve.

If the leak is intermittent the fault might be as simple as an oversized dish or something else putting pressure into the door and stopping it from shutting correctly.

On the other hand the door gasket could have come loose or become damaged.

Inspect the door seal and investigate for any cracks, a build-up of limescale or other deposits, or any areas where the seal has separated from the door.

Taking off the seal and also giving it a thorough wash has been known to help in some cases or you might need to acquire a new gasket and change it.

Water Inlet Valve (Solenoid Fill Valve)

The inlet valve can be another commonplace problem. It is in most cases found under the machine which means you will most likely have to take off the kick plate and might need to remove the door cover.

The fill valve opens and closes to allow water into the tub at varying parts of the programme. The inlet valve could be damaged, evidenced by a slight drip, or it might be broken thus not operating fully while the dishwasher is running.

In the case that the inlet valve fails to close correctly this can result in the dishwasher leaking.

Usually these valves are not able to be repaired unless it is just the rubber seal that is damaged, which means the whole part would have to be replaced.

Leaking Hoses

Hoses are needed to fill, drain and redistribute water during the cycle.

Two issues could develop where hoses are involved.

  1. The gaskets could get damaged or the connections might work loose so it’s worth having a look at all the connections first.
  2. The other problem than may easily happen over time is that hoses could become broken or cracked.

Luckily damaged hoses are relatively simple to procure and also change, even for a novice.

Pumps and Seals

You are able to visually check the seals that are part of the water pumps or motor to determine if there is a leakage and also change them if there is.

The Float Switch

The float itself or the float switch could be faulty resulting in the dishwasher overfilling.

A working float will lift up as the water level goes up until it reaches the maximum fill level. The tag of the float would then turn on the switch. A blockage or breakage could be your issues.

Checking the switch will require electrical equipment although it could be obviously broken in which case replacing it should stop the leak.

Alternative Parts that Could Result in a Leak

A broken wash arm or support may resulting in leakage. This can likewise often affect how well your dishes are being cleaned.

Broken or faulty lines could likewise cause this fault as could a loose pump cap if your machine has one.

The motor shaft seal could have degraded causing leakage. This generally presents as leakage coming from the underside of the appliance.

Top Tips to Mend Your Machine

  1. Spend less by replacing the seal rather than the entire part. In most instances, you can acquire the gasket without the rest of the part which saves you having to replace the whole part.
  2. Check the quick solutions first. There’s no point pulling the entire thing out if the problem is the detergent.
  3. Photograph your progress. This could help you reverse the process, show the component you are looking for to a sales person, and identify the fault to a repair person if needed.
  4. Be careful. Water and electricity do not mix so unplug the machine first.
  5. If you’re not sure get in a repair person.

What To Do Next If Your Trouble Shooting Fails to Identify or Mend the Leakage

If the cause of the leakage can’t be uncovered the next step you can take is to pull the dishwasher away from the wall to get better access underneath it and also fill it with water to find out whether the leakage becomes visible.

If you are still in the dark your dishwasher might only show a leakage when it’s running. If this is the case, your best bet would be to employ a qualified technician to determine as well as resolve the problem as there are safety risks of checking for faults with electrical components exposed.

More Dishwasher Problems:

  • Dishwasher Being Loud
  • Dishwasher Not Turning On
  • Dishwasher Not Draining
  • Dishwasher Not Drying
CLICK-TO-CALL